Go to home page
Aluminium constructions for your safety
Home > Products > Ladders > Retractable ladders > JOMY > Specification guide

JOMY Retractable Ladder - Specification guide

This guide contains more specifications about the used materials, construction, installation, protection, tests and guarantee of the ladder.

JOMY retractable ladder specification guide

1. General

  • Closed, the ladder resembles a metal column of 100mm x 110mm. It is installed at a distance of approx 60cm from the exit and has a minor effect on the facade esthetics.
  • The ladder opens perpendicular to the wall ( or optionally: parallel to the wall). A safety rail deploys from the mobile upright.
  • After opening, the top rung will be 75cm lower than the closed height. The ladder rests on the floor and runs approx 2.25m higher than the highest level of access so that the top rung is at level with the user's shoulder.

2. Materials

  • Only materials that are not subject to corrosion can be used: profiles of aluminum alloy, anodized 10 micron, natural mat finishing; fasteners (bolts, axes, springs and rivets) of stainless steel A2-70 DaN/mm2; and joint washers, bushes, etc. of polyamide.
  • No protective treatment, painting or maintenance is required, except when exposed to aggressive environments.
  • The outside parts of the closed ladder can be painted in any RAL color by polyester powder coating.

3. Construction

  • The ladder is assembled from standard modules.
  • One mobile and one fixed upright
  • Tubular rungs with anti-slip upper side, width: 60cm; useful width: 49cm; cross section at 37mm x 22.5mm, spaced at 30cm.
  • The lowest rung is positioned at a height of 60cm from the ground level
  • Lateral safety rail along the full ladder height deployed from the mobile upright providing a side protection of 30cm width
  • Opening handles at every point of access at any desired height, with a pitch of 30cm (standard: one opening handle per story). With a quarter turn of any handle, ladder deploys over complete height.
  • At each intermediate level, handles are permanently fixed to ladder; at ground level and at roof level, they can be removable
  • Ladder is balanced by stainless steel counterbalance springs; opens and closes with minimal effort; deploys softly
  • The ladder rungs have to be tested to carry a charge of 450kg on rungs and 5000kg on uprights.
  • The ladder's own weight is equal to or lower than 5 lb/ft or 7.5 Kg/m.
  • Ladders can be equipped with a lifeline according to standard EN353-1. The lifeline is based on a fixed aluminum rail and a step-less carriage, which blocks on the rail in case of a fall.

4. Installation

  • The ladder is installed without damaging the stability or safety of the façade. Special anchor brackets are installed at least every 1.5m using M12 expansion plugs or chemical anchors. Each support can withstand a horizontal force of 4000N.
  • The ladder has to be reinforced by a special U-channel for parts of the ladder that overshoot the building, parts that are placed at a distance from the wall, and parts that cannot be fixed to the wall every 1.5m. The reinforcement profile is attached to the wall at least every 3m.
  • The ladder can expand freely within its anchor brackets without deformation or damage to allow for thermal expansion.
  • The contractor will provide for a cleared surface of approximately 80cm x 80cm to allow unhampered opening of the ladder.

5. Tests

  • The ladder is submitted to static and dynamic examination tests by a certified body. The manufacturer will provide a copy of the test report on request.

6. Burglar-Proof

The ladder can be protected from use by unauthorized persons :

  • By not placing a deployment handle at ground level or at roof level;
  • By providing a locking hub and padlock for the ground and roof levels to prevent opening from those levels, while allowing opening from other levels;
  • By an opening detector, connected to the burglary alarm.

7. Guarantee

The ladder and installation have to be inspected. The inspection report needs to be submitted to the client within one month after installation.

Change language and region

Please select your language:
Please select your region:
Sélectionez votre région:
Kies uw regio:

Search this site

To be implemented


To be implemented

Sign in

You are not signed in. Sign in using your google account.

Signed in

You are logged in as: .

Sign in error

Something went wrong. We have not received your request. Please try submitting your request again, or contact us directly.. You are not signed in.



You are here: Home > Products > Ladders > Retractable ladders > JOMY > Specification guide


This site uses cookies. By continuing to browse this website, or by clicking "I agree" you consent to the use of cookies. What are cookies?